Brookfield General Purpose Silicone Viscosity Standard with Certificate of Calibration
 |
 |
|
Brookfield Viscosity Standards provide a convenient, reliable way to verify the calibration of your Brookfield Laboratory Viscometer/Rheometer. The fluids are stored in plastic bottles. Silicone viscosity standards supplied in 1000 mL plastic bottles complete with a certificate of calibration. Features and Benefits
|
General Purpose Silicone fluids are the most commonly used standard for verifying calibration of your AMETEK Brookfield laboratory Viscometers/Rheometers. Silicone Standards are Newtonian fluids which are accurate to ±1% of viscosity value. Silicone fluids provide excellent temperature stability and are less temperature sensitive than oil viscosity standards. AMETEK Brookfield Viscosity Standards are certified by methods traceable to the United States National Institute of Standards and Technology (NIST). The selection of one or two fluids will normally provide sufficient measurement points to verify calibration of your instrument. Fluids with a viscosity of 30,000 cP or greater are supplied in 16 oz (500 mL) containers, all other fluids are supplied in 24 or 32 oz (750 or 1000 mL) containers, complete with a certificate of calibration. Features and Benefits
|
- How do I choose a spindle and speed?
- Why do I need a viscosity standard?
- How many viscosity standards do I need?
- Should I use silicone oil or mineral oil?
- My fluid has a viscosity value that is not part of your standard fluids listing, what should I do?
- How do I know if my instrument is calibrated?
- What is the best calibration check that I can perform?
- Should I use an analog or digital model?
- How is viscosity affected by temperature?
- What is the accuracy of my Brookfield temperature probe?
- How long should I wait for thermal equilibrium?
- How do I calculate accuracy of the reading when testing a sample?
- How do I calculate CAP 1000/2000 accuracy?
- My dial reading and/or cP (viscosity) value won't stabilize, what does that mean?
- My spindle wobbles when it rotates - what does than mean?
- What is a math model and when should you use it to evaluate viscosity test data?
- My digital viscometers is display "EEEEE" when I am trying to test a material? What does that mean?
- What format is best to save data?
- Can PG Flash be used with my computer?
HOW DO I CHOOSE A SPINDLE?
Selecting a Spindle:
The process of choosing a spindle and rotational speed for use with your Brookfield viscometer is ultimately one of trial and error. However, there are several means to narrowing the possibilities before any testing is performed. If a sample has historically been tested using a particular speed and spindle combination, the user should use that same combination. This will help to ensure test results are accurate and repeatable. The objective is to choose a spindle that will produce a dial or digital display reading between 10% and 100% torque.
When the viscosity of a fluid is known:
The maximum viscosity range of a spindle running at a given speed is equal to the spindle factor multiplied by 100. This is the full scale range for that spindle/speed combination. The minimum viscosity that can be measured is equal to 10 times the factor, or one tenth of the full scale range. Knowing the full scale range, you can then determine if your fluid fits within the capabilities of that spindle/speed combination.
Additionally, digital viscometers equipped with the AUTO RANGE key allow the full scale range to be obtained automatically. Enter a spindle code and an RPM setting and press the AUTO RANGE key. The viscometer will calculate and display the full scale range viscosity for that spindle and speed combination.
When the viscosity of a fluid is not known.
If the reading is below 10% or above 100%, the user should choose a different speed to obtain a reading in the recommended range. If changing speeds doesn't provide readings between 10% and 100%, the user should try another spindle. Generally, if the reading is above 100% at the lowest speed, the next smallest spindle should be used. If the reading is below 10% at the highest speed, the next largest spindle should be used.
To test a fluid at multiple speeds, choose a spindle that will produce readings between 10% and 100% for at least three speed settings.
WHY DO I NEED A VISCOSITY STANDARD?
Viscosity standards are used to check the accuracy of your Brookfield viscometer. Brookfield Silicone and Mineral Oil Standards provide you with a fluid viscosity value that is constant at 25°C, making calibration verification easy to establish. Standards are a traceable part of calibration verification - an important component of many certifying quality systems like ISO, ASHTO, etc.
HOW MANY VISCOSITY STANDARDS DO I NEED?
Generally one or two is sufficient. Select a fluid with a viscosity value that fits the measuring range of the spindle and speed that you use most often.
SHOULD I USE SILICONE OR MINERAL OIL VISCOSITY STANDARDS?
This choice is dependent on your product. Silicone is used most often because it is less temperature sensitive. Some manufacturers, such as the paint industry, cannot have silicone in their process, so mineral oil becomes the choice.
Brookfield has specific recommendations:
Silicone
All viscometers using regular spindles, Small Sample Adapters and UL Adapters
High Temperature Silicone (HT)
All viscometers using the Thermosel accessory and Controllers
Mineral Oil
KU fluids for KU Viscometers
CAP fluids for CAP1000 and CAP2000 Viscometers
Special Purpose Mineral Oil
Encouraged for Wells/Brookfield Cone/Plate Viscometers
MY FLUID HAS A VISCOSITY THAT IS NOT PART OF YOUR STANDARD FLUIDS LISTING, WHAT SHOULD I DO?
The viscosity of your sample fluid is typically of little importance when checking the accuracy of your Brookfield Viscometer, because:
— your fluid may be non-Newtonian, so the viscosity will change; Brookfield Viscosity Standard fluids will not change with time or shear (rpm), making the calibration check more definable
— your Brookfield Viscometer is no more or less accurate at one range (rpm and spindle) than the next; if the Viscometer passes at one range, it can be considered to be calibrated throughout its entire range
.........with this in mind, you probably don't need a special order blend fluid
HOW DO I KNOW IF MY INSTRUMENT IS CALIBRATED?
Your Brookfield Viscometer/Rheometer is guaranteed to be accurate to +/- 1.0% of full scale range in use. You can check the accuracy of your Viscometer by performing a calibration check.
Calibration check for Viscometers/Rheometers using standard spindles:
You must use:
600 ml beaker; allow any air bubble to surface
controlled temperature 25.0°C (+/- .01°C); allow sufficient time for temperature equilibrium; this includes standards, spindle and guard leg
guard leg in place for LV and RV spindles
fluid that has been initially opened within in past 12 months
Accuracy for the calibration check is:
Instrument Accuracy is 1% of Full Scale range in use (FSR) and is added to Standard Fluid Accuracy which is 1% fluid value in cP.
Calculating accuracy for the Instrument:
FSR is the factor for the spindle and speed in use multiplied by 100; FSR can also be found on digital models, by selecting a spindle, speed and then pressing the AUTO RANGE button; the screen will then display a cP value @ 100% (of FSR); 1% of that displayed FSR is instrument accuracy.
Determining Accuracy for the Standard Fluid:
Fluid value is on the label of the jar, above the word "value", and is stated in cP(mPa·s). Calculate 1% of this value.
WHAT IS THE BEST CALIBRATION CHECK THAT I CAN PERFORM?
Test your Brookfield Viscometer/Rheometer with a Brookfield Viscosity Standard Fluid at 3 different rotational speeds to verify how the instrument responds when sensing low, medium, and high % torques.
Example:
RV Viscometer with RV #3 spindle at 20, 10, and 5 rpm
Brookfield Viscosity Standard Fluid: Nominal value = 5000 cP; Actual value = 4850 cP
SHOULD I USE A DIGITAL VISCOMETER OR A DIAL READING (ANALOG) VISCOMETER?
Viscosity results obtained from Brookfield instruments are reproducible regardless of whether an instrument is a dial reading or digital. Assuming that all other conditions are identical - spindle, speed, temperature, container size, spring torque, etc., a reading produced on a dial reading viscometer is as valid, accurate, and reproducible as a reading produced on a digital viscometer.
HOW IS VISCOSITY AFFECTED BY TEMPERATURE?
Generally speaking, viscosity has an inverse relationship with temperature. As temperature increases, viscosity decreases. For this reason, it is critical to control the temperature of a sample during any viscosity measurement.
WHAT IS THE ACCURACY OF MY BROOKFIELD TEMPERATURE PROBE?
Brookfield temperature accuracy is +/- 1 °C up to 150 °C, and +/- 2 °C above 150 °C up to 300 °C. This accuracy applies for RTDs in DV-I+ w/Temperature Probe, DV-II+, Programmable DV-II+, DV-II+ PRO, DV-III, DV-III+, Thermosel w/Model 74,75, 85 and 106 Controllers, CP/CPE-44PY cups, SC4-**RPY Chambers.
HOW LONG SHOULD I WAIT FOR THERMAL EQUILIBRIUM?
Thermal equilibrium is the state at which every element of a viscosity measurement is at a unified temperature. These elements include, but are not limited to, the spindle, guard leg, sample container, sample, and temperature probe. Because temperature is critical to accurate readings, you should allow sufficient time to achieve equilibrium. In general, one hour is the minimum time to wait. The more viscous the material being measured, the longer you should wait.
Recommendations for silicones in 600 mL beakers
5 - 500 cP = 1 hour
1000 - 12,500 cP = 2 hours
30,000 - 100,000 cP = 4 hours
Recommendations for silicones and mineral oils in accessories, Cone/Plate, CAP, SSA, and UL Adapters
10 - 20 minutes depending on volume
Recommendations for mineral oil for KU Viscometers
1 - 2 hours
HOW DO I CALCULATE ACCURACY OF THE READING WHEN TESTING A SAMPLE?
Accuracy is calculated as 1% of the full scale range (FSR) of the viscometer. FSR is defined as the highest achievable viscosity reading with a given spindle and speed. The easiest way to determine FSR is by pressing the AUTO RANGE button on your digital viscometer. Pressing this displays FSR for the spindle and speed entered. Taking 1% of this value gives you instrument accuracy. For dial viscometer users, multiplying your factor by 100 gives you FSR. Consequently, you can see that your factor is equal to your instrument accuracy.
HOW DO I CALCULATE CAP 1000/2000 ACCURACY?
Accuracy of the Brookfield CAP viscometer is based on two separate factors. The first factor is the accuracy of the instrument and the second is the accuracy of the calibration fluid. The total accuracy is the instrument accuracy plus the fluid accuracy.
Instrument accuracy is determined by consulting Table 3.1 in the CAP viscometer manual. The operator must determine whether the instrument is a high or low temperature CAP, and whether it is a 1000 or 2000 model. Cross referencing that information with the cone-spindle number in use, they will determine a number on the chart. This number is the percent of the full scale range that must be considered as the instrument accuracy.
For example: A CAP 1000H with cone spindle 3 at 900 rpm.
The operator must first determine the full scale range of the CAP for these conditions. By pressing the RPM button, the display will show 100% = X, X being the value in Poise of the full scale range. Under these conditions, FSR is 8.333 Poise. From Table 3.1, the percent of FSR calculated for accuracy is 2 or 4%, depending on whether the calibration fluid is greater or less than 50% of FSR.
If our calibration fluid is 4 Poise, we would calculate accuracy as 2% of FSR, or 2% of 8.333. Instrument accuracy would thus be .1666, rounded to .17 Poise. The fluid accuracy is 1% of 4 Poise, or .04 Poise. Thus total accuracy is .04 + .17, or .21 Poise.
MY DIAL READING AND/OR CP (VISCOSITY) VALUE WON'T STABILIZE - WHAT DOES THAT MEAN?
Most fluids demonstrate a "non-Newtonian" behavior that prevents them from ever displaying a constant centipoise value or dial reading. For more information on Newtonian and Non-Newtonian fluids, consult our free publication More Solutions to Sticky Problems.
MY SPINDLE WOBBLES WHEN IT ROTATES - WHAT DOES THAT MEAN?
The spindle may be bent; check the straightness against the dimensions in Appendix A of our publication of More Solutions To Sticky Problems. The jewel bearing, pivot point and shaft may be worn or bent; perform the calibration check to determine if the viscometer is still performing within calibration. The viscometer is in need of service and recalibration.
WHAT IS A MATH MODEL AND WHEN SHOULD YOU USE IT TO EVALUATE VISCOSITY TEST DATA?
Various math models were empirically developed by different researchers, in order to fit trends they saw in their own data sets. The Math Model is a "best fit" line that can be used to characterize data from a specific test and has the advantage for easy data storage and comparison with similar tests by looking at slope and y-intercept.
There are some simple models that provide a reasonable fit to many data sets, and have parameters that have some meaning to various practitioners - whether those people are researchers, QA/QC people, or process engineers. The modified Casson model, for example, works well for testing chocolates, among other things. The Herschel-Bulkley model is useful for materials that have a yield point and then "shear-thin" after yielding. This may be good for "gel-like" materials, for example.
Brookfield's "Analysis" module in our applications software (Rheocalc and Wingather) lists the curve-fit parameter results, along with a "Coefficient of Fit". One could try a few of our models, and select the one with the best "CoF", for example - the closer to "1.00", the better the fit. It may be tough to accurately predict product behavior. Conservatively used, rheology models may be good for interpolating apparent viscosities at various shear rates, for example. Nonetheless, some models may be used to extrapolate yield stresses, for example, at shear rate values of zero. The more data points taken, the more reliable the fit.
Please also bear in mind that a certain model may have been used just because it's "simple" and "good enough for a reasonable estimate". That does not mean that it would be the best model to use. One example is in the Petroleum industry: "drilling mud" rheology has been examined with the Bingham model for years, despite the fact that these materials are highly non-Newtonian! The Bingham model assumes Newtonian behavior after yield. Nonetheless, field personnel felt it is was "good enough" to give them an idea of how the material was handling. More practitioners have started using the "H-B" model during the past few years.
MY DIGITAL VISCOMETERS IS DISPLAY "EEEEE" WHEN I AM TRYING TO TEST A MATERIAL? WHAT DOES THAT MEAN?
A display of "EEEEE" on a digital viscometer means the reading is over-range. That is, for the spindle and speed you have selected, the material is reading higher than the Full Scale Range. Lower the speed or change the spindle to raise the Full Scale Range.
WHAT FORMAT IS BEST TO SAVE DATA?
We recommend saving data in both the native form and as ".CSV" files.".CSV" files can be read by both ASCII/Plain Text (e.g., MS-Notepad(tm)) readers and MS-Excel(tm) spreadsheets.
CAN PG FLASH BE USED WITH MY COMPUTER?
PG Flash is only for downloading programs to the viscometer. Rheocalc-T should be used for acquiring data to a PC when used with DV2T or DV3T.