- Acid Corrosive Cabinets
- Arabidopsis Chambers
- Air Compressors
- Anemometer
- Autoclaves
- Balances
- Baths
- Blenders
- BOD Measurement
- Bunsen Burners
- Calibration Weights
- Calorimeters
- Cell Disruptors Ultrasonic
- Cell Manipulation
- Centrifuges
- Chemical Oxygen Demand
- Chromatography Columns & Consumables
- Climate Chambers
- Circulating Coolers
- Cold Boxes
- Colony Counters
- Colorimeters and Photometers
- Conductivity Meters
- Cryogenics
- Density Meters
- Desiccator
- Dissolved Oxygen
- Dispersers
- Dry Block Heaters
- Electrophoresis
- Flocculator
- Freezer Dryers
- Fume Hood Safety Containments
- Furnances
- Glove Box
- Hazardous Storage Cabinets
- Gas Generators
- Heating Mantles & Tapes
- Humidity Cabinets
- Hotplates
- Ice Machines
- Incubators
- Kjeldahl Equipment
- Laboratory Air Drying Cabinet or Warming Cabinet
- Laboratory Glasswashers and Accessories
- Liquid Handling Products
- Melting Point
- Microbiological Safety Cabinets
- Microscopes
- Milling
- Mixers
- Mixing and Storage Vessels
- Multi Parameters Meters
- Organisers and Bins
- Ovens
- PCR Workstation and UV Cabinets
- Plant Growth Cabinets
- Pellet Presses
- Personel Protective Equipment
- pH Measurement
- Pumps
- Refractometers
- Refrigeration - Refrigerators and Freezers
- Rheometers
- Rotators
- Rotary Evaporator
- Shakers
- Sieve Shakers
- Spare Parts
- Specialist Application Products
- Spectrophotometers
- Stirrers
- Stomachers
- Thermal Cyclers
- Toxic Substance Cabinets
- Titration
- Turbidity
- Ultrasonic Cleaners
- Ultra Violet Products
- Vacuum Chambers
- Vibratory Feeder
- Viscometers
- Water Purification Systems
- Water Stills
- Demonstration Stock
Jenway PFP7/C Clinical Flame Photometer, supplied with Na, K and Li filters, connecting hoses and clips, compressor plug and drain trap (230V/ 50Hz)
Technical Specification
| Parameter | PFP7/C |
| Range | 120 to 160mmol/l Na, 0 to 10.0mmol/l K |
| Limits of detection Na | 0.2ppm |
| K | 0.2ppm |
| Li | 0.25ppm |
| Reproducibility | <1% coefficient of variation for 20 consecutive samples using 10ppm Na set to read 50 |
| Linearity | < 2% error when 3ppm Na/K and 5ppm Li are set to read 100 |
| Stability | < 2% drift over 5min when continuously aspirating 10ppm sample set to 50.0. Specificity Interference from Na/K and Li equal in concentration to test element will be <0.5% |
| Recorder output | Nominal 1.00V for a reading of 100.0 |
| Electrical supply | 90–125V or 190–250V @50/60Hz |
| Air supply | Moisture and oil free, 6 litre/min @ 14psi |
| Fuel | Propane, butane, natural gas or LPG |
| Size (w x d x h) | 420 x 360 x 300mm |
| Weight | 8kg |
PFP7/C Clinical Flame Photometer
• Designed for clinical analysis
• Supplied with Na, K and Li filters
• Low temperature, single channel
• Flame failure safety system
• Operates with propane, butane, natural gas or LPG
• 3 year warranty
The PFP7/C is a low temperature, single channel flame photometer that is specifically designed for use in clinical applications for the determination of sodium, potassium and lithium. The in-built lineariser circuitry of the PFP7/C enables readings of both sodium and potassium to be displayed directly in mmol/l.
• Supplied with Na, K and Li filters
• Low temperature, single channel
• Flame failure safety system
• Operates with propane, butane, natural gas or LPG
• 3 year warranty
The PFP7/C is a low temperature, single channel flame photometer that is specifically designed for use in clinical applications for the determination of sodium, potassium and lithium. The in-built lineariser circuitry of the PFP7/C enables readings of both sodium and potassium to be displayed directly in mmol/l.
The Jenway flame photometers are not supplied with the following accessories but some, e.g. the air compressor and gas regulators, are necessary to run the flame photometer.
A water separator is recommended to remove any residual water from the compressed air supply. The size of water separator required depends on the local humidity. If there is high humidity then the large water separator is recommended.
Gas regulators are needed to regulate the pressure of fuel being inputted into the flame photometer.
A fuel filter is recommended to ensure that no particulates get into the mixing chamber from the fuel supply.
To complement the Jenway range of flame photometers there are several calibration standards offered to enable accurate calibration of the flame photometer. All calibration standards are 500ml unless otherwise stated.
Ordering Information
| Part Code | Description |
| 535 001 | Air compressor (230V/ 50/ 60Hz) |
| 535 002 | Air compressor (110V/ 60Hz) |
| 500 176 | Water separator (small) |
| 500 177 | Water separator (large) |
| 500 093 | Fuel filter |
| 500 178 | Butane regulator |
| 500 179 | Propane regulator |
| 500 180 | Natural gas regulator |
Calibration Standards
| Part Code | Description |
| 025 008 | 1.00mmol/l Li |
| 025 004 | 100mmol/l Na, 100mmol/l K |
| 025 006 | 140mmol/l Na, 5mmol/l K |
| 025 007 | 120mmol/l Na, 2mmol/l K |
| 025 005 | 160mmol/l Na, 8mmol/l K |
| 025 027 | 160mmol/l Na, 80mmol/l K |
| 025 021 | 1000ppm Na |
| 025 023 | 1000ppm K |
| 025 024 | 1000ppm Li |
| 025 025 | 3000ppm Ba |
| 025 009 | 1000ppm Ca |
| 025 171 | Cleaning solution (1 litre) |
Miscellaneous
| Part Code | Description |
| 500 134 | Dust cover |
| 500 019 | Nebuliser |